Fix Truck Axle Threads On Skateboard & Longboard
Fix Truck Axle Threads On Skateboard & Longboard


100 thoughts on “Fix Truck Axle Threads On Skateboard & Longboard”

  1. Nicholas Figueroa says:

    So I went to my local skate shop and picked up a skate tool. Just got into longboarding and had $10 so I bought the one without the die. I figured I wouldn't need it. I came home and cleaned and lubed my bearings and while putting on the axle but, JUST MY LUCK it stripped the nut. Now I have to wait until tomorrow to fix it. Ugh

  2. Joshua Williams says:

    How do you remove the dye from the tool

  3. Mike Zula says:

    Is there any way to do this without a die?

  4. Dezmond sk8ter says:

    What are the waders for

  5. Dezmond sk8ter says:

    Washers

  6. xhonestx says:

    hey my axle or nut is like spinning there but not coming off at all, how do i solve this? ists either the axle thread or the nut which i cant seem to tell

  7. Lucas Riedel Sandkilde says:

    whatever he og other skaters say, there is no advantage of not tightening your wheels fully. the inner ring of the bearing is meant to be stationary, whilst the rest of the bearing is what should turn. it is loud and inconvinient not to tighten it fully. scooter wheels are tightened fully, and they spin for several minutes.

  8. Bensaii says:

    any tips if your axle is damaged and you cant even get the wheel off to re-thread it?

  9. Jack Reeves says:

    the pig skate tool has a threader also

    just sayin

  10. Young Winners says:

    hey i was wondering if you can tell me how to get a stripped bolt off of a truck cause my axle is'int stripped its my bolt so if you try to loosen it it tightens up so i was wondering if you can make a video on how to get a stripped bolt off of a truck for me cause you are a skateboard genius so if you can it would be really helpful 
    thanks

  11. MrBarryThor says:

    If you dont have this tool just put the nut on top of the truck and hammer it down until it gets past the bent threads and then screw it on it'll re-thread it when you screw

  12. Fingerboarderusa1275 says:

    What kind of wheels?

  13. jay pruitt says:

    I wont to see you  skate

  14. Adrian Salgado says:

    Can you do this on hollow axles or will it mess it up? Need HELP on this!

  15. asianboyy97 says:

    shit, my axle is so fucked up, i cant get the die in. suggestions?

  16. danny cram says:

    how do you fix it if the nut is stuck on

  17. Eddie Johnson says:

    Is there a way you can rethread the axle if you don't have the tool? Help please

  18. diver dave says:

    if your using the old fashion die with the long handles … take the axle off the skate board – then you can easily turn the tool.
    be sure to use cutting oil or wax with your die cutter and work slowly

  19. Zachary Daly says:

    What skate tool does he use I need one like that

  20. foolishonboards says:

    Great Vid, one of a kind!

  21. Generation2k18 says:

    Die what size??

  22. Noah Cagle says:

    You always say "now I can go skate" but I've always wondered if you suck or not

  23. Burt Bobain says:

    justmdont.buy these shit wheels. buy wheels that protect your axles. like.oldschool wheels.and.some.good manufacturers.

  24. Lee Ratcliff says:

    When you are using a die to cut or clean a thread always use a lubricant like trefolex. Also, you never cut a thread in one pass (constantly turning the die in the one direction until the end) do a half turn or so then back it off a quater turn to let the swarf clear the die (thats why the die has three or more cutouts around it, to help clear swarf out and not get clogged up and jamed). Keep doing this until you have reached the end of the thread. If you don't clear the swarf out it can jam up the die and thread and cut a really nasty notchy/broken thread or worse strip/cross the thread completely, which means new truck time.

  25. Nick Morales says:

    cool

  26. skatecm1 says:

    The top of my axle is still in bad shape & I cant fit the bolt at all. What can I do?

  27. Orionskate says:

    can you tell me what so special about skateboard truck nut(wheels) ,i buy some in the hardwere store  and i cant screw it on the truck.only skate nuts can be mounted?only in skate shop you can get this skate nuts?

  28. Miguel Bravo says:

    I lost my nut and washer for my wheel.what should i do.

  29. Jorge Barajas says:

    My 2 screws won't come off from the trucks what do I do to be able to actyally get them off?

  30. Zachary says:

    i worked on my skate with the die and after 10 minutes we saw change but we couldn't fit the nut on. Is it possible to not be able to retread an axle?

  31. Benjamin Hahn says:

    Thank you so much I thought I was going to have to buy new trucks until I saw this! The tools only cost me $20 and the best part is I can do this as many time as I need until my trucks snap! Thanks rat vision you saved me tons of money!

  32. matias pakkanen says:

    Thx boy now i cam finaly change my wheels

  33. Mark Mendoza Hernandez says:

    0:23 I totally have that tool! I saw it at the shop when buying my full setup and instinctively thought I'm going to need this in the near future!

  34. Josh Makhan says:

    hey man I used a 5/16 and it's not the right size where can I get a smaller size rethreader?

  35. Alex Dopest says:

    My bolt is stucked on the trucks and its like stripped on their , does anyone know what tool to use ?

  36. Jesse Buehler says:

    alien workshop makes those kinds of tools too

  37. PunkSkaful says:

    I'm poor but now I can afford one but fuck this city, there is no skate tool for sale here so I cut the tip of my axle for about 2 mm and it worked! I can skate like Dustin Dollin

  38. #ligmagang says:

    Do a video on the difference between plastic trunks vs metal trunks

  39. Isaac Samano says:

    I have a different tool, but it also has that axle fixer. but it can't come off, so when I try to use it with the tool on it, it never gets a grip of the axle. plz help, it never works.

  40. conner cannaday says:

    my trucks turn in opposite directions so i keep going strait how can i fix it

  41. HoxenStorm says:

    My wheel is stuck on my trucks please help.

  42. Sergio Ayala says:

    lol i just used a claw hammer and rethreaded it by hand

  43. Cardaysing55 says:

    anyone have any thoughts???? braaaand new pudwill grizzly trucks and i couldnt get them to tighten very much… i have never put so much force into tightening a nut before i i think i almost broke my vise grip wrench to get it to turn and then again to get it off??? bad trucks? or something else?

  44. Gangster Chicken Nugget says:

    my truck is bent or something, it looks crooked and turns to the left on its own

  45. Patrick Lunardi says:

    I swear americans use the stupidest measurements… Why in the fuck would someone make the axle of 7.9 mm (5/16 inch) instead of 8??! What were they thinking??!

  46. sparkels Espindola says:

    yo dudes can someone tell me how to repair the wheels of the skateboard its cause I feel like I'm gonna fall this never happened to me plz help

  47. Dakota Patel says:

    My nut on one axle won't come off what do I do to get it off thanks!

  48. Tyler Grogg says:

    Can someone help? I took my wheels out to clean my bearings, which I'm never doing again, and I tightened the nut as tight as I could get it so the bearings would be in. When I tried to loosen it, it wouldn't come off. I've only had these trucks a few months. This happened to the last pair. Please help ASAP!

  49. n1ko says:

    are washers really necessary ? i have only one and its in the inside, so should i also put one on the outside?

  50. Jude Laygo says:

    how to fix a lostthread nuts? :/

  51. Alejandro Hernández says:

    Please help, my kingpin is stuck on my truck and i want to replace it. Btw the head of the kingpin is Allen (hexagonal) aka bristol.

  52. DaniDaimondz Official says:

    my nut from the axle was hit on the concrete and now i cant remove my wheels
    how i can remove that?

  53. the goat says:

    Why don't you guys post anymore

  54. WillSkates says:

    Guys don't waste your money on a utilitool just get a Pig Wheels skate tool for so much cheaper!

  55. TheLostLT says:

    my nuts holding my wheels on like to come loose but all my threads look fine..

  56. F34R SWADE says:

    wow👏 this was really useful and informable. this is the tool I was looking for and I really need this thx for making a video like this it is truly one of the best videos ever that was actually helpful👏.

  57. Samantha Nicole Bismonte says:

    How can I prevent to damage my truck axle thread when skataboarding?

  58. Carlos Ochoa says:

    my wheel wont come off my trucks i think the bearings are rusted on my axle what do i do?

  59. Pablo Ramon says:

    please make a video of the best engineered skateboarding wheel.
    I'm dying to know which one i should stick to.
    thank you PR

  60. teh soljn says:

    well i have a question my truck axle threads are really damaged and i cant get out the wheels to fix it how can i get them out without destroy my trucks plz 😀

  61. John Toth says:

    amazing

  62. Joshua Hong says:

    does it work with hollow trucks?

  63. Kasen Haddix says:

    This was really helpful, I fixed the thread but the problem now is that I don't have the bolt anymore because it was damaged when I took it off the truck. Does anyone know the dimensions for the wheel nut? Like thread size and what have you? Thanks ahead of time for anyone that knows!

  64. Drago Noise says:

    could someone please help me if the skateboard trucks are moving is it broken

  65. Bj Garcia says:

    can i just hacksaw the axle abit instead of using the die?

  66. pimp boi says:

    nylon nuts are the best nuts

  67. normie says:

    I have that tool

  68. Sebastian Gallardo says:

    this guy is the most formal, civilized skater ive ever seen

  69. Richard keith says:

    remember people let your hand do the turning

  70. G Mac says:

    Do you have any tips to get the nut off a stripped thread. It just keeps spinning. The wheel is still on and I want to get it off.

  71. Jayden Cobner says:

    …but what if I don't have the tool?

  72. KevinT says:

    is there a way to do this without a die?

  73. born tolose says:

    Thank you. Your video helps me as a beginner a lot. I hope you make more informative video like these. Looking faward. Greeting from Thailand 🙂 #landofsmile

  74. Arjun Melwani says:

    The axle nut on my trucks, with the wheels on the truck is stripped, how do I remove the axle nut?

  75. backyard motorcross says:

    silver t tool is better

  76. Barry Zadikoff says:

    You could always repair the nut with a tap tool.

  77. Andreas Egersett says:

    see this is crap about not tightening the axel nut all the way down the only thing that should stop you from doing so is not having a spacer between your bearings. if you have one between them and you tighten it down then it makes you bearings work properly

  78. Kingofthegames says:

    oh i never do this

    when my axle breaks i just get a plank of wood and beat the fucking bolt on

  79. Fun On The Run says:

    What if the threads on the nut make it turn in place, like it won't come off?

  80. cupsole skater says:

    what size is the axle nut cant find it anywhere

  81. Nigel 0251 says:

    My nut is broken on my kingpin what should u do when that happens i can not replace my bushings

  82. luca hagger says:

    Good boy

  83. rhen alvarez says:

    the axle nut with the wheels on the trucks is stucked how to remove the axle nut?

  84. Carlos Chavez says:

    okay i have my nut cross threaded and cant remove it from the axle, it just spins in place on the end. does anything help?

  85. Blue_Yoshi says:

    And what if you dont have neither?

  86. Kane's Crimes says:

    It's 2018 but the description below took place in 2007…
    …so it balances out…
    …right?…

    I once fixed my "mushroomed" axle with a knife and a nail…and another hanger.
    I used the knife tip like a chisel and the hanger to tap the knife tip through the "mushroomed-over" threads(of which there were 3-1/2) ,and then I ran the edge of the blade through the "new" threads to open'em up a little more and twisted on a nut from a previous set of trucks.
    It worked out alright, but if I had used a die I would've been able to skate for an extra hour or two that day.

  87. Whaler says:

    My motherfucking axle nut is literally stuck. Won't budge! New god damned longboard. Came just a week ago.

  88. Anthony A says:

    How did u get the nut off the truck?!?! I can't get the nut off the truck it just spins when i try to take it off PLZ HELP

  89. Mr. J says:

    Fix the nut wtf

  90. Dealex L says:

    Is it okay to not have washer

  91. Ineedsomefriends says:

    I want to see you skate

  92. T Pham says:

    Super informative man thanks

  93. Chicago Dan says:

    “Deep grooves and sharp threads”. I’m naming my first album that

  94. BlueJay says:

    i have an M8 1,25 die, will it be the same as a 5/15" 24 die?

  95. Vicky Miller says:

    I love you

  96. Психолог Николай Лу says:

    love ur channel man, buying some wheels tomorrow

  97. Hunter Memmer says:

    Not sure if its just me but i just put the nut on and just deal with it

  98. Exile says:

    So sick ima fix my indys

  99. Labowski UnderAchiever says:

    I always thought the die thingy on some tools were for rollerskates or inlines … 🤔 And now I know 😄

Leave a Reply

Your email address will not be published. Required fields are marked *