How to replace front anti roll bar link / front drop link on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]
How to replace front anti roll bar link / front drop link on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]


Required tools:
Wire brush
WD-40 spray
Copper grease
HEX bit No.H5.
Combination spanner #17
Drive socket # 10
Drive socket # 17 Wheel impact socket #17
Ratchet wrench
Torque wrench
Phillips Screwdriver
Hydraulic transmission jack
Wheel chock 1. Raise the front of the car and secure on supports. 2. Unscrew the wheel bolts.
Use wheel impact socket #17. AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts. 3. Chock the opposite wheel.
Use a hydraulic transmission jack. 4. Clean the stabiliser link fasteners.
Use a wire brush.
Use WD-40 spray. 5. Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17.
Use a ratchet wrench. 6. Unscrew and remove the wheel arch cover fasteners.
Use a drive socket #10. Use a ratchet wrench.
Use a Phillips screwdriver. 7. Remove the wheel arch cover. 8. Clean the stabiliser link fasteners.
Use a wire brush.
Use WD-40 spray. 9. Unscrew the fasteners connecting the stabiliser link to the stabiliser bar.
Use HEX No.H5. Use a combination spanner #17.
Use a ratchet wrench. 10. Remove the stabilizer rod. AUTODOC recommends:
Examine stabiliser bushes. Replace them if needed. 11. Install a new rod, tighten the fasteners. 12. Tighten the fastener connecting the stabilizer link to the stabilizer bar.
Use a combination spanner #17. Use HEX No.H5.
Use a torque wrench.
Tighten it to 55 Nm torque. 13. Remove the hydraulic transmission jack. AUTODOC recommends:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms. 14. Tighten the fastener connecting the stabilizer link to the shock strut.
Use a combination spanner #17. Use HEX No.H5.
Use a torque wrench.
Tighten it to 55 Nm torque. 15. Install the wheel arch cover to its mounting seat. 16. Install and tighten the wheel arch cover fasteners.
Use a drive socket #10. Use a ratchet wrench.
Use a Phillips screwdriver. 17. Clean the wheel rim mounting seat.
Use a wire brush. Treat the contacting surface.
Use copper grease. 18. Screw in the wheel bolts.
Use wheel impact socket #17. AUTODOC recommends:
To avoid injury, hold up the wheel when screwing in the fastening bolts. 19. Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench.
Tighten it to 110 Nm torque.

2 thoughts on “How to replace front anti roll bar link / front drop link on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]”

  1. Алексей A. says:

    Good 👍👍👍

  2. autodoc.co.uk says:

    Have a look at other videos on our channel:

    🔸 FIAT BRAVO 2 (198) car repair tutorial — https://www.youtube.com/playlist?list=PLWep5LzT0sxnXSk_ZGV8EQNE0u0xsEvuC

    🔸 How to replace front suspension arm / front control arm on FIAT BRAVO 2 (198) —
    https://youtu.be/N6DNLhkK0nk

    🔸 How to replace oil filter and engine oil on FIAT BRAVO 2 (198) —
    https://youtu.be/OfKqsiakJ64

    🔸 How to replace wipers blades / window wipers FIAT BRAVO 2 (198) —
    https://youtu.be/LiRQdUC3LyU

    🔸 How to replace a front shock strut on FIAT BRAVO 2 (198) — https://youtu.be/_VMKHSPNhjc

Leave a Reply

Your email address will not be published. Required fields are marked *