How to replace rear wheel bearing / rear hub bearing on PEUGEOT 206 1 (2D) [TUTORIAL AUTODOC]
How to replace rear wheel bearing / rear hub bearing on PEUGEOT 206 1 (2D) [TUTORIAL AUTODOC]


Required tools:
Wire brush
WD-40 spray
Brake cleaner All-purpose cleaning spray
Copper grease
Torx bit T30
Drive socket # 19 Drive socket # 32
Wheel impact socket #19
Ratchet wrench
Torque wrench
Tap wrench Hammer
Round-nose pliers
Flat chisel
Rubber mallet Impact screwdriver
3-Arm Gear Puller
Crow bar
Wheel chock 1. Raise the rear of the car and secure on supports. 2. Unscrew the wheel bolts.
Use wheel impact socket #19. AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts. 3. Remove the retaining springs of the brake pads.
Use a crowbar. 4. Remove the brake pad retaining pin.
Use round-nose pliers. 5. Clean the brake caliper fasteners.
Use a wire brush. Use WD-40 spray. 6. Remove the retainer of the brake pads.
Use a crowbar. Use a rubber mallet. 7. Remove the brake pads.
Use a crowbar. 8. Clean the brake caliper fasteners.
Use a wire brush. Use WD-40 spray. 9. Unscrew the brake caliper fastening.
Use a drive socket #19. Use a ratchet wrench. 10. Remove the brake caliper. AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system. Make sure that the brake caliper is not hanging on the brake hose. Don’t press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary. 11. Clean the brake disc fasteners.
Use a wire brush. Use WD-40 spray. 12. Unscrew the brake disc fastening
Use Torx T30. Use an impact screwdriver. 13. Remove the brake disc. 14. Remove the hub bearing protection cap.
Use a crowbar. Use a hammer. AUTODOC recommends:
Some cars are not equipped with wheel hub caps. 15. Unstake the wheel hub retaining nut.
Use a flat metal-working chisel. Use a hammer. 16. Unscrew the wheel hub axle nut.
Use a drive socket #32. Use a tap wrench. 17. Remove the hub and the bearing together, since they are a sealed unit. Use 3-Arm Gear Puller. 18. Clean the hub bearing mounting seat.
Use all-purpose cleaning spray. 19. Install the new wheel hub with a bearing. 20. Tighten the hub. Use a drive socket #32.
Use a torque wrench. Tighten it to 155 Nm torque. AUTODOC recommends:
The wheel bearing unit must not tilt on the axle pin. 21. Restake the wheel hub retaining nut.
Use a flat metal-working chisel. Use a hammer. 22. Install the hub bearing protection cap.
Use a rubber mallet. 23. Clean the hub. Use a wire brush.
Treat the contacting surface. Use copper grease. 24. Install the brake disc. 25. Tighten the brake disc fastening. Use Torx T30. Use a torque wrench. Tighten it to 9 Nm torque. 26. Install the brake caliper and fix it. Use a drive socket #19. Use a torque wrench. Tighten it to 80 Nm torque. 27. Install the brake pads. 28. Install the retainer of the brake pads.
Use a crowbar. 29. Install the brake pad retaining pin. 30. Install the retaining springs of the brake pads. 31. Treat the surface where the brake disc contacts the wheel rim. Use copper grease. 32. Clean the brake disk surface.
Use a brake cleaner. AUTODOC recommends:
After applying the spray, wait a few minutes. 33. Screw in the wheel bolts.
Use wheel impact socket #19. AUTODOC recommends:
To avoid injury, hold up the wheel when screwing in the fastening bolts. 34. Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench.
Tighten it to 120 Nm torque.

1 thought on “How to replace rear wheel bearing / rear hub bearing on PEUGEOT 206 1 (2D) [TUTORIAL AUTODOC]”

  1. Алексей A. says:

    Good 👍👍👍

Leave a Reply

Your email address will not be published. Required fields are marked *