How to replace rear wheel bearing / rear hub bearing on VW CADDY 3 (2KB) [TUTORIAL AUTODOC]
How to replace rear wheel bearing / rear hub bearing on VW CADDY 3 (2KB) [TUTORIAL AUTODOC]


1. Unscrew the wheel bolts.
Use wheel impact socket #17. 2. Raise the rear of the car and secure on supports. AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts. 3. Spread the brake pads.
Use a crowbar. Remove the connector of the brake pad wear sensor.
Use round-nose pliers. Please note!
Some cars are not equipped with the brake pad wear sensor. 6. Unscrew the caliper bracket fastening. Use a drive socket #16.
Use a ratchet wrench. Remove the brake caliper together with its bracket. AUTODOC recommends: Tie the caliper to the suspension or to the
body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.
Make sure that the brake caliper is not hanging on the brake hose. Don’t press the brake pedal after the brake caliper has been
removed. As a result, the piston can fall out from he brake cylinder, and brake fluid leakage and depressurization of the system may occur. 7. Unscrew the brake disc mounting bolts and remove it.
Use Torx T30. AUTODOC recommends:
If necessary, use a rubber mallet. 8. Pry the hub cap with a screwdriver and remove it.
If necessary, use a flat chisel and a hammer. 9. Unscrew the wheel hub axle nut.
Use HEX No.19. 10. Remove the hub and the bearing together, since they are a sealed unit.
Use 3-Arm Gear Puller. 11. Clean the guiding part of the stub axle.
Use a wire brush. AUTODOC recommends:
Be careful to avoid damaging the guiding part of the stub axle. AUTODOC recommends:
Be careful to avoid damaging the guiding part of the stub axle. AUTODOC recommends:
Be careful to avoid damaging the guiding part of the stub axle. 13. Install the new wheel hub with a bearing.
Move the hub as far as it can go. 14. Tighten the hub. Use HEX No.19.
Use a torque wrench. Tighten it to 200 Nm torque. AUTODOC recommends:
The wheel bearing unit must not tilt on the axle pin. 15. Apply some copper grease to the hub where it contacts the brake
disk. 16. Install the brake disc. 17. Tighten the brake disc fastening. Use Torx T30.
Use a torque wrench. Tighten it to 9 Nm torque. 18. Clean the mounting seats of the caliper and its bracket.
Use a wire brush. Use WD-40 spray. 19. Install the cap of the hub nut. AUTODOC recommends: The cap must always be replaced. When
you install the previously used cap the sealing will be lost. Use a torque wrench.
Tighten it to 80 Nm torque. 21. Install the ABS sensor cable in the holder on the brake caliper. Connect
the ABS sensor electric socket. Connect the brake pad wear sensor plug. 22. Clean the hub. Use a wire brush.
Treat the contacting surface. Use copper grease. 23. Screw in the wheel bolts.
Use wheel impact socket #17. 24. Lower the car and working in a cross order, tighten the wheel
bolts. Use a torque wrench. Tighten it to 120 Nm torque.

3 thoughts on “How to replace rear wheel bearing / rear hub bearing on VW CADDY 3 (2KB) [TUTORIAL AUTODOC]”

  1. Saša Đokić says:

    Врхунски
    Видео !
    😁😁😁😁😁😁😁😁😂😂😁😀😀😀😀😀😀😀😀😀😀😀😀😀😀☺☺☺☺☺☺☺☺☺☺☺

  2. autodoc.co.uk says:

    🛠️The tools you need to replace rear wheel bearing:

    – Torx bit T30

    – HEX bit No.H19

    – 3-Arm Gear Puller

    – flat screwdriver

    – flat chisel

    – hammer

    – round nose pliers

    – ratchet wrench

    – drive socket No. 16

    – torque wrench

    – wheel impact socket No.17

    – wire brush

    – WD-40 spray

    – brake cleaner

    – copper grease

    – multipurpose grease

    – rubber mallet

    – crow bar

    – wheel chock

  3. Muhamed Bunjaku says:

    Good job 🥽🗜🔧🛠 🙂

Leave a Reply

Your email address will not be published. Required fields are marked *